Drahtlose SecurView-Internetkamera für Tag- und Nachtaufnahmen
TV-IP121W (Version A1.0R)
- Sichtweite bei Nacht bis zu 5 m
- Keine Ethernet-Verbindung erforderlich: Videodaten werden über sicher verschlüsseltes drahtloses Signal übertragen
- Kostenlose Software mit Funktionen für Bewegungserkennung und E-Mail-Benachrichtigungen
- Kompakte Internetkamera lässt sich auf den meisten Oberflächen anbringen
DISCONTINUED PRODUCT
The TV-IP121W (Version A1.0R) has been discontinued. It has been replaced by the TV-IP324PI (Version v1.0R). For a list of discontinued products, click here.Hilfsprogramme
Dateiname: Utility_IPSetup(v1.0.0.8).zip
SHA-1 Checksum: 8BAB782BCB8F5C9792A9A03B5DEA651D235F8CB0
Datum: 7/25/2017
Dateigröße: 719.16 KB
Dateiname: Utility_SecurView(V1.2.0.21).zip
SHA-1 Checksum: A1FA7F7428BB3D0D6772BFB8B0492A7AF9072794
Datum: 7/25/2017
Dateigröße: 50.83 MB
Firmware
Aktualisieren Sie die Firmware von TRENDnet-Produkten NICHT über eine drahtlose Verbindung. Wenn die Firmware über eine drahtlose Verbindung aktualisiert wird, kann das Produkt Schaden nehmen. Führen Sie Aktualisierungen deshalb bitte nur über verdrahtete Verbindungen durch. |
Firmware Version: V1.1.1 build 36
Release Date: 4/2013
Notes:
- Upload.asp removed.
- Updated save configuration file encryption type.
Notes:
Dateiname: FW_TV-IP121W_A1(1.1.1.36).zip
SHA-1 Checksum: 756BC9CAE1B8986DAC135AE25DE4EEB5C175E329
Datum: 7/25/2017
Dateigröße: 3.05 MB
NE PAS faire de mise à niveau d’un firmware sur quelque produit TRENDnet que ce soit à l’aide d’une connexion sans fil. Les mises à niveau de firmware via une connexion sans fil peuvent endommager le produit. Veuillez faire les mises à niveau de firmware uniquement avec un réseau filaire |
Firmware en français seulement: Si votre appareil dispose d'une version du firmware 1.1.0 build 13, Veuillez mettre à jour le firmware avec cette Version.
Firmware Version: V1.1.1 build 5
Date de sortie: 4/2013
notes:
- Upload.asp supprimé.
- Mis à jour le fichier de sauvegarde de configuration type de cryptage.
Notes:
Dateiname: FW_TV-IP121W_FRENCH(V1.1.1.5).zip
SHA-1 Checksum: 41864ABA75935D39C0AE78D55C7E6E24ABE3B2C4
Datum: 7/25/2017
Dateigröße: 2.93 MB
Datenblätter
Dateiname: EN_Spec_TV-IP121W(A1.0R).pdf
Datum: 12/20/2013
Dateigröße: 881.76 KB
Dateiname: FR_Spec_TV-IP121W(A1.0R).pdf
Datum: 12/20/2013
Dateigröße: 885.67 KB
Dateiname: GE_Spec_TV-IP121W(A1.0R).pdf
Datum: 12/20/2013
Dateigröße: 882.35 KB
Dateiname: SP_Spec_TV-IP121W(A1.0R).pdf
Datum: 12/20/2013
Dateigröße: 871.82 KB
Dateiname: RU_Spec_TV-IP121W(A1.0R).pdf
Datum: 12/20/2013
Dateigröße: 1.87 MB
Dateiname: IT_Spec_TV-IP121W(A1.0R).pdf
Datum: 12/20/2013
Dateigröße: 860.63 KB
Kurzanleitung zur Installation
Dateiname: EN_Web_TV-IP121W(A1).pdf
Datum: 3/28/2013
Dateigröße: 2.24 MB
Dateiname: FR_Web_TV-IP121W(A1).pdf
Datum: 3/28/2013
Dateigröße: 2.25 MB
Dateiname: GE_Web_TV-IP121W(A1).pdf
Datum: 3/28/2013
Dateigröße: 1.77 MB
Dateiname: PO_Web_TV-IP121W(A1).pdf
Datum: 5/16/2013
Dateigröße: 1.72 MB
Dateiname: SP_Web_TV-IP121W(A1).pdf
Datum: 3/28/2013
Dateigröße: 1.77 MB
Dateiname: RU_Web_TV-IP121W(A1).pdf
Datum: 5/16/2013
Dateigröße: 2.55 MB
Dateiname: EST_Web_TV-IP121W(A1).pdf
Datum: 3/28/2013
Dateigröße: 1.71 MB
Bedienungsanleitung
Dateiname: UG_TV-IP121W(A1.31).pdf
Datum: 3/28/2013
Dateigröße: 2.97 MB
Produktbild(er)
OverviewPlease ensure you have followed the quick installation guide and have the camera setup and accessible on your home/office network. The following instructions are going to outline how to make a SecurView camera accessible over the Internet. We will start by assigning a unique static IP addres...
The files cannot be accessed through the camera. Dismount the USB memory stick from the camera and connect it to your computer....
The USB page does not automatically update, refresh the page
The USB stick may not be formatted in FAT, to check connect USB stick to your computer. Go to My Computer right click on the USB stick go to Properties look for File System....
Yes, they can be disabled. Log in to the camera by entering the camera's IP address into your browser. The default IP address is https://192.168.10.30. The default username and password are both "admin".
Click on Setup and then go to the Basic>System page. The IR LED control can be set to "o...
The camera must be configured properly to have Internet access. This includes making sure you have entered a valid default gateway address for the camera and valid DNS server entries to ensure it can resolve names.
Unfortunately the camera does not support SSL. If the email provider requires SS...
Unfortunately the cameras from different families do not share a common, free, application and cannot be used together. SecurView cameras will not function in IPView Pro and vice versa....
By default the camera uses TCP port 80. Forward this port in your router or firewall to the camera.
Unfortunately SecurView is not compatible with Macintosh operating systems.
The camera can be configured from a Macintosh through its web-based configuration page. The camera's web configuration page can be reached by entering its IP address into a web browser. For example, if the IP address is 192.168.10.30 you would access it by opening your web browser and entering 192.1...
The camera's web configuration page can be reached by entering its IP address into a web browser. For example, if the IP address is 192.168.10.30 you would access it by opening Internet Explorer and entering 192.168.10.30 into the address line....
What is the default IP address of my TV-IP121W and TV-IP121WN?
...
Log in to the camera and click on Setup. Click on Motion Detect on the left hand side. On this page you can setup two motion detection windows. Under "Window" you can select either 1 or 2. Place a check in "Enable" to turn on motion detection. You can adjust the threshold for each window individuall...
Warning:
Firmware upgrade failure may permanently damage the unit and cause it to malfunction. Do not interrupt the firmware upgrade process by disconnecting it from the network or unplugging its power from the power outlet once the firmware upgrade process has begun. Never perform a firmware upgr...
Log in to the camera and click on Setup then click on Event Server>Email on the left hand side. Enter your email server and user information here.
After applying the email server information click on Event Config on the left hand side. You have three options, Motion Detection, Scheduled uplo...
Log in to the camera and click on Setup then click on Event Server>FTP on the left hand side. Enter your FTP server information here.
After applying the FTP server information click on Event Config on the left hand side. You have three options, Motion Detection, Scheduled uploading and GPIO trig...
After you have the camera configured on your network start SecurView. Click on the "Settings" button then click on the "Add Camera" button. It will search your network for any supported cameras and display a list of them. Highlight the camera you want to view in SecurView then click "Add Camera".
...
The supported browsers are Internet Explorer 6.0 or above.
Windows 7 (32/64-bit), Vista (32/64-bit), XP (32/64-bit)
Press and hold in the reset button on the back of the camera for approximately 10 seconds while the power is on to restore the factory default settings. ...
The top LED is a power light. It should be a steady orange light when power is applied to the camera. The bottom LED is a link light. It should be green and blinking when sending and receiving data. ...
Log in to the camera by entering the camera's IP address into your browser. The default IP address is https://192.168.10.30. The default username and password are both "admin".
After you have logged into the camera do the following.
-Click Setup
-Click Basic>User
You can define the Adm...
Log in to the camera by entering the camera's IP address into your browser. The default IP address is https://192.168.10.30. The default username and password are both "admin".
After you have logged into the camera do the following.
-Click Setup.
-Click Network>Wireless.
-Click the Site Su...
Yes, the camera does support DDNS (Dynamic DNS). Dynamic DNS services will allow you to maintain a single hostname for the camera, even if your ISP changes your WAN IP address. The camera will update the DDNS record to reflect the new IP address. This ensures that each time you go to the hostname yo...
You will need to forward the port that the camera is using in the router to the camera. By default this is TCP port 80. From a remote location you would enter in the public or WAN IP address of your router into your browser or add it to SecurView using the public IP address.
Refer to your router'...
| Kamera | |
| Allgemein | Sensor: 1/4" color CMOS-SAuflösungensor Resolution: 640 x 480 pixels Brennweite: 4.5mm F/No: F2.8 (Bord-Objektiv) Minimum illumination: 0.5 Lux @ F2.8 Sichtwinkel: 60 Grad diagonal |
|---|---|
| Audio | Eingebautes vollständig schwenkbares Mikrofon Empfindlichkeit:: -48dB +/- 3dB (5 meters max) Frequenzbereich: 50~16000Hz Codec: PCM |
| Bild & Video | Kompression: MJPEG Auflösung: VGA (640x480), QVGA (320x240), QQVGA (160x120) bis zu 30fps Belichtung/Weißabgleichregelung: automatisch Bildwechsel : vertikal/horizontal Lichtfrequenz: 50Hz, 60Hz oder Außenbereich |
| Hardware | |
| Netzwerk | IEEE 802.3u 10/100Mbps Fast Ethernet, Auto-MDIX |
| LED | Stromversorgung, Link/Aktivität |
| IR Wellenlänge | 850nm |
| Rücksetztaste | Reset Einstellungen |
| Stromverbrauch | 6 watts (max) |
| Stromversorgung | 5V DC, 2.5A (Externes Netzteil) |
| Abmessungen (B x T x H) | 70 x 100 x 57mm (2.67 x 3.94 x 2.95 in.) |
| Gewicht | Kamera: 165g (5.8 oz.) Stehen: 135g (4.76 oz.) |
| Temperatur | Funktionieren: 0°C ~ 45°C (32°F ~ 113°F) Lagerung: -15°C ~ 60°C (14°F ~ 140°F) |
| Zulassungen | CE, FCC |
| Anforderungen (SecurView™) | |
| Für die Sicht | Internet Explorer 6.0 oder höher |
| Softwarebetrieb | Windows 2000, XP, Vista |
| SecurView™ Software | Kanal: Unterstützung von bis zu 16 Kameras Aufnahme/Playback/Bewegungsmeldung/Audio |
| Drahtlose Verbindung | |
| Standards | IEEE 802.11b/g |
| Frequenzbereich | 2.412 ~ 2.484 GHz |
| Antenna | Eine abnehmbare 2dBi-Antenne mit Reverse-SMA-Anschluss |
| Sicherheit | 64/128-bit WEP, WPA-PSK, WPA2-PSK |
| Einstellungen | |
| Bild | Helligkeit, Kontrast, Sättigung, Schärfe, Weißabgleich, Flip, Spiegelung(horizontal/vertikal) |
| Aufnahme | Aufnahmeart: ereignisbasiert (Bewegungsmeldung und digitaler Eingangsauslöser), fortlaufende und planmäßig Speichergröße: 32MB (Minimum) |
| Schnappschuss | Ereignisauslösend: Bewegungsmeldung Aktion: Warnungs-Email abschicken und/oder mit FTP hochladen |
| Port Einstellungen | HTTP port: 80 (Rückstellung) |
| digitaler Zoom | 3x |
| Dynamisches DNS | Ja |
| Uhrzeit | Mit NTP Server synchronisieren oder Zeit/Datum manuell einstellen |
PACKUNGSINHALT |
|
Alle erwähnten Geschwindigkeiten dienen ausschließlich dem Vergleich. Produktspezifikationen, Größe und Form unterliegen unangekündigten Änderungen, und das tatsächliche Aussehen des Produkts kann von dieser Beschreibung abweichen.
