Videocamera IP wireless n SecurView
TV-IP110WN (Version v2.0R)
- Copertura fino a 4 volte maggiore rispetto alle videocamere IP wireless g
- Visualizza, registra e gestisci funzioni avanzate da qualsiasi connessione internet
- Registrazione in base al rilevamento di movimento, allarmi e-mail e tante altre funzioni con il software supplementare
- Connessione WPS (Wi-Fi Protected Setup) al semplice tocco di un pulsante
DISCONTINUED PRODUCT
The TV-IP110WN (Version v2.0R) has been discontinued. It has been replaced by the TV-IP324PI (Version v1.0R). For a list of discontinued products, click here.Firmware
NON aggiornare il firmware di un prodotto TRENDnet mediante connessione wireless. L'aggiornamento del firmare mediante connessione wireless può danneggiare il prodotto. Eseguire l'aggiornamento del firmware solo con connessione di rete cablata. |
Release Date: 4/2013
Notes:
- Upload.asp removed.
- Updated save configuration file encryption type.
Notes:
Nome del file: FW_TV-IP110WN_V2(1.2.2.68).zip
SHA-1 Checksum: 2124722741F630A71236FDDD4C5E5F3C69C80852
Data: 7/25/2017
Dimensioni del file: 4.15 MB
Firmware: V1.2.2.65
Release Date: 3/2012
Note:
- Date/Time stamp added for Internet Explorer
- To complete the firmware update process you must perform a factory reset after the firmware upgrade
- To record the Date/Time stamp in TRENDnetView Pro, you must upgrade the software to TRENDnetView Pro (2.0.0.0)_03032012
Nome del file: FW_TV-IP110WN_V2(1.2.2.65).zip
SHA-1 Checksum: 9C6B51C19B8C552863592E568C4E2213E9586A3C
Data: 7/25/2017
Dimensioni del file: 4.14 MB
NON aggiornare il firmware di un prodotto TRENDnet mediante connessione wireless. L'aggiornamento del firmare mediante connessione wireless può danneggiare il prodotto. Eseguire l'aggiornamento del firmware solo con connessione di rete cablata. |
Release Date: 2/2012
Notes:
- Improved security
Note:
- Please do not save the camera's configuration file from the old firmware and restore it after the firmware upgrade
- After a successful firmware upgrade, please reset the camera to factory default and reconfigure the camera. We strongly recommend that you change the camera's administrator's account password
Nome del file: FW_TV-IP110WN_V2(1.2.2.64).zip
SHA-1 Checksum: 7505D4A17DFDE063079A504A39D5052E803A3FCD
Data: 7/25/2017
Dimensioni del file: 4.13 MB
Software
Version: 2.1.1.294
Release Date: 6/2012
Notes:
- Enhanced Functionality
Download TRENDnetView Pro Guida per l'utente
Nome del file: SecurViewPro(2.1.1.294).zip
SHA-1 Checksum: 37413E7BE0E60F3F91AC8EF11F282FCCF621C2B0
Data: 7/25/2017
Dimensioni del file: 27.81 MB
IP View Pro Software has been superceded by TRENDnetView Pro. To download TRENDnetView Pro, please see the TRENDnetView Pro entry.
Nome del file: Utility_IPSetup(v1.0.0.9).zip
SHA-1 Checksum: DF2576962235590F425CAB35246A68886DD0C6C9
Data: 7/25/2017
Dimensioni del file: 700.14 KB
Version: 2.0.0.0
Release Date: 3/2012
Nome del file: SecurViewPro(v2.0.0.0)_03032012.zip
SHA-1 Checksum: C1450A708E10F8F0947868EC11E57F675214D45A
Data: 7/25/2017
Dimensioni del file: 73.88 MB
Scheda tecnica
Nome del file: EN_spec_TV-IP110WN(v2.0R).pdf
Data: 8/4/2011
Dimensioni del file: 4.91 MB
Nome del file: FR_spec_TV-IP110WN(v2.0R).pdf
Data: 8/4/2011
Dimensioni del file: 4.92 MB
Nome del file: GE_spec_TV-IP110WN(v2.0R).pdf
Data: 8/4/2011
Dimensioni del file: 4.92 MB
Nome del file: PO_spec_TV-IP110WN(v2.0R).pdf
Data: 9/27/2011
Dimensioni del file: 4.96 MB
Nome del file: SP_spec_TV-IP110WN(v2.0R).pdf
Data: 8/4/2011
Dimensioni del file: 4.93 MB
Nome del file: RU_spec_TV-IP110WN(v2.0R).pdf
Data: 8/4/2011
Dimensioni del file: 4.90 MB
Nome del file: IT_spec_TV-IP110WN(v2.0R).pdf
Data: 8/4/2011
Dimensioni del file: 4.93 MB
Guida rapida per l'installazione
Nome del file: EN_Web_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 3.43 MB
Nome del file: FR_Web_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 3.47 MB
Nome del file: GE_Web_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 2.89 MB
Nome del file: PO_Web_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 2.71 MB
Nome del file: SP_Web_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 2.87 MB
Nome del file: RU_Web_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 3.85 MB
Nome del file: EST_Web_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 2.50 MB
Guida per l'utente
Nome del file: UG_SecurViewPro.pdf
Data: 6/1/2012
Dimensioni del file: 4.66 MB
Nome del file: UG_TV-IP110WN(2.01).pdf
Data: 8/3/2011
Dimensioni del file: 5.22 MB
Immagine/i del prodotto
OverviewPlease ensure you have followed the quick installation guide and have the camera setup and accessible on your home/office network. The following instructions are going to outline how to make a SecurView camera accessible over the Internet. We will start by assigning a unique static IP addres...
The camera must be configured properly to have Internet access. This includes making sure you have entered a valid default gateway address for the camera and valid DNS server entries to ensure it can resolve names.
Unfortunately the camera does not support SSL. If the email provider requires S...
Unfortunately the cameras from different families do not share a common, free, application and cannot be used together. SecurView cameras will not function in IPView Pro and vice versa....
By default the camera uses TCP port 80. Forward this port in your router or firewall to the camera.
Unfortunately SecurView is not compatible with Macintosh operating systems.
The camera can be configured from a Macintosh through its web-based configuration page. The camera's web configuration page can be reached by entering its IP address into a web browser. For example, if the IP address is 192.168.10.30 you would access it by opening your web browser and entering htt...
The camera's web configuration page can be reached by entering its IP address into a web browser. For example, if the IP address is 192.168.10.30 you would access it by opening Internet Explorer and entering https://192.168.10.30 into the address line....
The camera by default is configured to receive an IP address via DHCP. If it is unable to receive an IP address via DHCP it will default to 192.168.10.30. You can use the IP Setup Utility to find and change the IP address of the camera as well. Click Start and go to All Programs under TRENDnet to fi...
Log in to the camera and click on Setup. Click on Motion Detect on the left hand side. On this page you can setup two motion detection windows. Under "Window" you can select either 1 or 2. Place a check in "Enable" to turn on motion detection. You can adjust the threshold for each window individuall...
Warning:
Firmware upgrade failure may permanently damage the unit and cause it to malfunction. Do not interrupt the firmware upgrade process by disconnecting it from the network or unplugging its power from the power outlet once the firmware upgrade process has begun. Never perform a firmware upgr...
Log in to the camera and click on Setup then click on Event Server>Email on the left hand side. Enter your email server and user information here.
After applying the email server information click on Event Config on the left hand side. You have three options, Motion Detection, Scheduled uplo...
Log in to the camera and click on Setup then click on Event Server>FTP on the left hand side. Enter your FTP server information here.
After applying the FTP server information click on Event Config on the left hand side. You have three options, Motion Detection, Scheduled uploading and GPIO...
After you have the camera configured on your network start SecurView. Click on the "Settings" button then click on the "Add Camera" button. It will search your network for any supported cameras and display a list of them. Highlight the camera you want to view in SecurView then click "Add Camera".
...
The supported browsers are Internet Explorer 6.0 or above.
Windows 7 (32/64-bit), Vista (32/64-bit), XP (32/64-bit)
Press and hold in the reset button on the back of the camera for approximately 10 seconds while the power is on to restore the factory default settings. ...
The top LED is a power light. It should be a steady orange light when power is applied to the camera. The bottom LED is a link light. It should be green and blinking when sending and receiving data. ...
Log in to the camera by entering the camera's IP address into your browser. The default IP address is https://192.168.10.30. The default username and password are both "admin".
After you have logged into the camera do the following.
-Click Setup
-Click Basic>User
You can define the Admin...
Log in to the camera by entering the camera's IP address into your browser. The default IP address is https://192.168.10.30. The default username and password are both "admin".
After you have logged into the camera do the following.
-Click Setup.
-Click Network>Wireless.
-Click the...
Yes, the camera does support DDNS (Dynamic DNS). Dynamic DNS services will allow you to maintain a single hostname for the camera, even if your ISP changes your WAN IP address. The camera will update the DDNS record to reflect the new IP address. This ensures that each time you go to the hostname yo...
You will need to forward the port that the camera is using in the router to the camera. By default this is TCP port 80. From a remote location you would enter in the public or WAN IP address of your router into your browser or add it to SecurView using the public IP address.
Refer to your router'...
| Videocamera | |
| Informazioni generali | Sensor: 1/4” color CMOS image sensor Risoluzione: 640 x 480 pixels Obiettivo Lente focale: 5.0mm Apertura (F/No): F2.8 Illuminazione minima: 1 Lux Angolo di visualizzazione diagonale: 52 ° |
| Imaggini & Video | Compressione: MJPEG esposizione/bilanciamento dei bianchi/controllo di guadagno: automatico Risoluzione: fino a 25fps inVGA (640x480), 25fps inQVGA (320x240), 25fps in QQVGA (160x120) |
| Audio | Microfono omnidirezione entrocontenuto Sensibilità: -48dB +/- 3dB (massimo 5 metri) Frequenza: 50~16000Hz |
| Hardware | |
| Rete | IEEE 802.3u 10/100Mbps Fast Ethernet, Auto-MDIX |
| Esposizione di LED | Alimentazione, collegamento |
| Pulsante reset | Ripristina la configurazione di fabbrica |
| Consumo elettrico | 5 Watts |
| Alimentazione | Adattatore d'alimentazione esterno 5V, 2.5A |
| Dimensioni | 70 x 100 x 57mm (2.7 x 3.9 x 3.0 in.) |
| Peso |
|
| Temperatura |
|
| Umidità | Max. 90% (senza condensa) |
| Certificazioni | CE, FCC |
| Requisiti | |
| Interfaccia di gestione | Internet Explorer 6.0 o successive |
| Per eseguire SecurView Pro | Windows 7 (32/64-bit), Vista (32/64-bit), XP (32/64-bit) |
| SecurView Pro | Canali: supporta fino a 32 telecamere Memorizza/Playback/Rivela Moto |
| Protocolli di rete | TCP/IP, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, FTP, HTTP, PPPoE, UPnP e SSL |
| Senza Fili | |
| Standard | Basato su tecnologia IEEE 802.11n compatibile con reti IEEE 802.11b/g |
| Frequenza | 2.4 ~ 2.4835GHz |
| Antenna | 1 x Antenna dipolo staccabile 2dBi con Connettore SMA Reverse |
| Velocità dati (auto fallback) |
|
| Cifratura | 64/128-bit WEP, WPA/WPA2-PSK |
| Potere dell'uscita |
|
| Sensibilità di ricezione |
|
| Canali | 1~11 (FCC), 1~13 (ETSI) |
| Gestione | |
| remoto | Gestione remota supportati |
| Salvare / recuperare | Salvare / recuperare i file di configurazione |
| impostazioni | |
| Memorizzazione | Tipo di memorizzazione: Continuo, programmato o rilevamento movimento con software |
| Regolazione Porte | HTTP porta: 80 (default) |
| zoom digitale | 3x |
| DNS dinamico | Si |
| Tempo | Sincronizza con server NTP o seleziona tempo/data manualmente |
| SMTP | Funzione di posta SMTP con supporto per 2 account |
| Log sistema | 100 immissioni (max) |
CONTENUTO DELLA CONFEZIONE |
|
Tutti i riferimenti relativi alla velocità sono solo a scopo comparativo. Le specifiche, le dimensioni e la forma del prodotto sono soggette a modifiche senza preavviso e l'aspetto effettivo può differire da quello raffigurato nel presente documento.
