10 dBi Wireless N300 Outdoor PoE Access Point
TEW-740APBO (Version v3.1R)
- Wireless N300 point-to-point networking (2.4 GHz)
- Supports Access Point (AP), Wireless Distribution System (WDS), Client Bridge + AP, Wireless ISP (WISP) + AP, CPE + AP, and control AP (CAP) modes
- Built-in 10 dBi directional antenna
- Proprietary PoE power adapter included
- 1 x 10/100Mbps PoE-in port, and 1 x 10/100Mbps port
Firmware
Firmware applies to /A version only. **If upgrading from firmware version 3.02 or below to 3.03 or above, use the webimg_TEW-740APBO_X_old_upg file to upgrade (Firmware file is included in this download)** **If upgrading from firmware version 3.03 or above, use the webimg_TEW-740APBO_X file to upgrade (Firmware file is included in this download)** |
**Download the correct firmware file depending on your device region, A or EU. **The (A) version file applies to devices with /A noted on the device label. The (EU) version file applies to devices with the /EU or /UK noted on the device label. |
DO NOT upgrade firmware on any TRENDnet product using wireless connection. Firmware upgrade over wireless connection may damage the product. Please perform firmware upgrade with "wired" network connection only |
TEW-740APBO H/W: v3.1R
Firmware Version : 3.05K
Release Date: 1/2023
Note:
- Updated curl version 7.86.
- Updated openssl package version 1.1.1s.
- Updated dnsmasq version 2.88.
- Fixed cgi command injection vulnerability.
Firmware applies to /A version only. **If upgrading from firmware version 3.02 or below to 3.03 or above, use the webimg_TEW-740APBO_X_old_upg file to upgrade (Firmware file is included in this download)** **If upgrading from firmware version 3.03 or above, use the webimg_TEW-740APBO_X file to upgrade (Firmware file is included in this download)** |
**Download the correct firmware file depending on your device region, A or EU. **The (A) version file applies to devices with /A noted on the device label. The (EU) version file applies to devices with the /EU or /UK noted on the device label. |
DO NOT upgrade firmware on any TRENDnet product using wireless connection. Firmware upgrade over wireless connection may damage the product. Please perform firmware upgrade with "wired" network connection only |
TEW-740APBO H/W: v3.1R
Firmware Version : 3.05
Release Date: 1/2023
Note:
- Updated curl version 7.86.
- Updated openssl package version 1.1.1s.
- Updated dnsmasq version 2.88.
- Fixed cgi command injection vulnerability.
Datasheet
Quick Installation Guide
User's Guide
Product Images
Standards |
|
---|---|
Hardware Interface |
|
Special Features |
|
Access Control |
|
QoS |
|
Operation Modes |
|
SSID |
|
Internet Connection Types (WISP (CPE) + AP & Router modes) |
|
Management/Monitoring |
|
Frequency |
|
Wireless Channels |
|
Modulation |
|
Media Access Protocol |
|
Antenna Gain |
|
Wireless Output Power |
|
Receiving Sensitivity |
|
Power |
|
Operating Temperature |
|
Operating Humidity |
|
Certifications |
|
Dimensions |
|
Weight |
|
Warranty |
|
PACKAGE CONTENTS |
|
* Effective wireless coverage may vary depending on the wireless device's output power, antenna gain, antenna alignment, receiving sensitivity, and radio interference. Additionally, environmental factors such as weather conditions, physical obstacles, and other considerations may affect performance. For optimal results, we recommended consulting a professional installer for site survey, safety precautions, and proper installation.
** For optimal PoE distance from the PoE injector to the wireless access point, it is recommended to use a Cat 5e or better solid wire cable and connect the injector’s power supply directly to a power outlet. Avoid using a power strip or surge protector.