Search FAQs
Browse by Product
FAQ Home Page > Surveillance > IP Cameras > TV-IP300
Browse TV-IP300 Questions
There are 21 questions found in this category:

  1. How to setup the Internet Camera for Remote Viewing over the Internet
    OverviewPlease ensure you have followed the quick installation guide and have the camera setup and accessible on your home/office network. The following instructions are going to outline how to make a SecurView camera accessible over the Internet. We will start by assigning a unique static IP addres...
  2. How do I set a password on my TV-IP300(w)?
    Step 1 Open your web browser and type the IP address of the TV-IP300(w) in the address bar. The default IP address is 192.168.0.30. Step 2 Click on “System Administration”. Step 3 Click on the System link at the top of the page.  Step 4 Enter a password into the admin pa...
  3. What do the LED’s on the front of the camera mean?
    LED (1) Link light.  Steady Red light shows a good connection.  The light will flash when sending or receiving data. LED (2) Power light.  Steady Blue light confirms that the camera is powered on.   ...
  4. How do I reset my TV-IP300(w) back to factory defaults?
    Step 1 Locate the reset button on the back of the unit Step 2 Disconnect the power supply. Step 3 Press and hold in the reset button. Step 4 While holding in the reset button; reconnect the power supply. Step 5 Continue to hold in the reset button for approximately 10 seconds to restore ...
  5. How do I add user accounts to my TV-IP300(w)?
    Step 1 Open your web browser and type the IP address of the TV-IP300(w) in the address bar. The default IP address is 192.168.0.30. Step 2 Click on “System Administration”. Step 3 Click on the User’s link at the top of the page. Step 4 Enter the desired username and pas...
  6. What are the minimum system requirements for the IPView SP software?
  7. Which web browsers will allow me to view the video from a TV-IP300(w)?
    Internet Explorer 5.0 and above.
  8. How do I view the TV-IP300(w)’s image using IPView SP?
    Step 1 Start the IPView SP application by clicking on Start>All Programs>IPViewSP>IPViewSP Step 2 Click on “Camera 1”. . Step 3 Enter the IP address, port and protocol.  Also enter in the username and password if you have assigned one to the camera.  Click &ld...
  9. How do I configure my TV-IP300(w) series cameras to upload snapshots to an FTP server?
    Step 1 Open your web browser and type the IP address of the TV-IP300(w) in the address bar. The default IP address is 192.168.0.30. Step 2 Click on “System Administration”. Step 3 Click on the System link at the top of the page.  Fill in the FTP section and click save. ...
  10. How can I email snapshots based on motion from my camera?
    Step 1 Open your web browser and type the IP address of the TV-IP300(w) in the address bar. The default IP address is 192.168.0.30. Step 2 Click on “System Administration”. Step 3 Click on the System link at the top of the page. Fill in the SMTP section and click save. Note: Th...
  11. Can my TV-IP300(w) series camera use Power over Ethernet?
    No, it does not support Power over Ethernet.
  12. How do I upgrade the firmware of my camera?
    Step 1 Start the IPView SP application by clicking on Start>All Programs>IPViewSP>IPViewSP. Step 2 Click “System Configuration”. Step 3 Click “Tools”. Step 4 Click “Browse” and locate the firmware file and click open. Step 5 Click “...
  13. How do I configure the camera to record motion?
    Step 1 Open your web browser and type the IP address of the TV-IP300(w) in the address bar. The default IP address is 192.168.0.30. Step 2 Click on “System Administration”. Step 3 Click on the Motion Detection link at the top of the page. Step 4 Place a check mark in “E...
  14. How can I view the TV-IP300(w) remotely if it’s behind a router or firewall.
    Each camera behind a firewall or router will need four ports forwarded for audio and video streaming.  The four default ports are: 80 (TCP) HTTP Port 8481 (TCP/UDP) Control Channel Port 8482 (TCP/UDP) Audio Channel Port 8483 (TCP/UDP) Video Channel Port   If you are ins...
  15. What is the default IP address of my TV-IP300(w)?
    The default IP address is 192.168.0.30
  16. How can I configure my TV-IP300(w) through the web-based configuration?
    Open your web browser and type the IP address of the TV-IP300(w) in the address bar. The default IP address is 192.168.0.30....
  17. How do I configure my computer's IP address?
    For Windows 2000/XP users:- On the Desktop, right click on My Network Places > select Properties > right click on the Local Area Connection > select Properties, the Local Area Connection Properties Window will appear - Under General tab, select Internet Protocol (TCP/IP) > click on Properties button...
  18. When I enter the IP address of the camera, the image does not load, why?
    Please make sure all the Active X features are enabled for your Internet Explorer. 1. Go to Tool (on the Tool bar) > Internet options > Security2. Click on Custom Level and make sure all ActiveX controls are set to "Enable" and click OK.3. Once you save the settings, the browser will load again and ...
  19. How do I view the Internet Camera's live images within my Local Network?
    Open a web browser (Internet Explorer or Netscape), type your Internet Camera's IP address (i.e.: 192.168.0.30) in the Address bar, and then hit the Enter key. The Welcome page of the Internet Camera will appear. ...
  20. Can I replace the camera lens?
    The Internet Camera's Lens is replaceable with a standard CS-Mount type lens.
  21. The image is blurry, how do I fix this?
    You can adjust the Internet Camera's focus by rotating the lens.